Quick Search
Melment F 10 is used for cement and calcium sulphate based materials.
Melment F 10 is used for dry mortar products.
Melment F 10 is used self-levelling underlayments (SLU), Feather-edge products, Non-shrink grouts, Cementitious floor screeds, Cementitious self-levelling floor screeds, Tiles adhesives and joint fillers, Repair mortars, and Dry-mix concrete.
CAS Number: 25214-70-4
EC Number: 246-350-2
Molecular Formula: C12H18N2O3
SYNONYMS:
MELMENT F 10, Melment F10, MELMENT, Melment, Melamine-formaldehyde resin, Methylated melamine resin
Melment F 10 is a free-flowing, spray dried powder of a sulphonated polycondensation product based on melamine.
Melment F 10 is a powder-form superplasticizer based on melamine sulfonate, used in the bagged manufacturing of powder products such as cement and plaster.
The dosage of Melment F 10 is determined based on laboratory tests.
Melment F 10 is free-flowing spray dried powder of a sulphonated polycondensation product based on melamine.
Melment F 10 is used superplasticizer for cement and calcium sulphate based materials.
Melment F 10 is a construction additive plasticizer powder.
Melment F 10 is designed for plasticization and water reduction of cement and calcium sulphate-based materials.
Melment F 10 is a free-flowing, spray dried powder of a sulphonated polycondensation product based on melamine.
Melment F 10 is processed in conformity with international standards using certified chemical compounds with the help of highly advanced techniques.
Melment F 10 is meticulously tested by our vendors on well defined parameters to ensure its optimum quality, precise pH value and purity.
After dissolving in water: Melment F 10 is a component for concrete superplasticization; a ready-to-use concrete superplasticizer.
Melment F 10 is optimized for plasticization and reduction of water consumption for cement- and gypsum-based mixtures.
USES and APPLICATIONS of MELMENT F 10:
Melment F 10 is especially optimized for plastification and water reduction of cement based materials.
Melment F 10 is used self-levelling underlayments (SLU), Feather-edge products, Non-shrink grouts, Cementitious floor screeds, Cementitious self-levelling floor screeds, Tiles adhesives and joint fillers, Repair mortars, and Dry-mix concrete
Melment F 10 uses concrete admixtures & Concrete Plasticizers.
Melment F 10 is used for cement and calcium sulphate based materials
Melment F 10 is a free-flowing, spray dried powder of a sulphonated polycondensation product based on melamine.
Scope of application of Melment F 10: In powder form: self-leveling coatings; liquid mortar for mechanized application; repair mortar; tamponade mortar; tile adhesives and joint fillers; moldable and industrial plaster; finishing plaster; medical and dental solutions; plasterboards and partitions; and ceiling tiles and panels.
Other applications: Melment F 10 is especially optimized for plastification and water reduction of cement and calcium sulphate based materials; Including the following: Self-leveling underlayments (SLU), Feather edge products, Cementitious floor screeds, Dry-mix concrete, Repair mortars, Non-shrink grouts, Cementitious self leveling floor screeds, and Tile adhesives and joint fillers.
Melment F 10 is used for dry mortar products.
Melment F 10 is a high-performance superplasticizer for cement and calcium sulphate based materials
Melment F 10 is especially optimized for plastification and water reduction of cement and calcium sulphate based materials.
Melment F 10 provides an excellent development of early strength.
Fields of application of Melment F 10 are Self-levelling underlayments (SLU), Feather-edge products, Non-shrink grouts, Cementitious floor screeds, Cementitious fast-setting floor screeds, Repair mortars, Tile adhesives and joint fillers, Dry-mix concrete, and Great for gypsum casting.
Melment F 10 is used cementitious self-levelling floor screeds, cementitious flowable floor screeds, non-shrink grouts, feather-edge products, repair mortars and injection mortars.
Melment F 10 is used in the construction chemicals industry, cement-based powder manufacturing.
Melment F 10 is used in the construction chemicals industry, in gypsum-based powder manufacturing.
Melment F 10 is used in places where it is difficult to transport liquid superplasticizer.
Melment F 10 is used in the production of molding plaster in industry.
Melment F 10 is used self-levelling underlayments (SLU), feather-edge products, non-shrink grouts, cementitious floor screeds, cementitious self-levelling floor screeds, tiles adhesives and joint fillers, repair mortars, dry-mix concrete.
Melment F 10 is free-flowing spray dried powder of a sulphonated polycondensation product based on melamine.
Melment F 10 is used for cement and calcium sulphate based materials.
-Fields of Application Melment F 10 is especially optimized for plastification and water reduction of cement and calcium sulphate based materials, e.g.
self-levelling underlayments (SLU)
feather-edge products
non-shrink grouts
cementitious floor screeds
cementitious self-levelling floor screeds
tile adhesives and joint fillers
repair mortar
-Melment F 10 is especially optimized for plastification and water reduction of cement and calcium sulphate based materials; including the following:
• Self-leveling underlayments (SLU)
• Feather edge products
• Cementitious floor screeds
• Dry-mix concrete
• Repair mortars
• Non-shrink grouts
• Cementitious self leveling floor screeds
• Tile adhesives and joint fillers
ADVANTAGES OF MELMENT F 10:
Melment F 10 increases the durability of powder products by reducing the mixing water.
While Melment F 10 reduces the mixing water of powder products, it increases their workability.
Melment F 10 does not change the colors of powdered products.
Melment F 10 can be easily mixed with water on site to obtain liquid superplasticizer.
FEATURES AND BENEFITS OF MELMENT F 10:
*No temperature sensibility
*Compatible with other additives like Stabilizers (Methylcellulose) or *Redispersible Powder Polymers
*Compatible with air entraining agents
*No change of surface tension (air entraining)
*No delay of cement hydration / strength development
HOW TO MIX DIRECTIONS OF MELMENT F 10:
How to mix with Cementitious Material:
Mix pre-mixed concrete or cement with plasticizer, Melment F 10, for a few minutes, then add water (mix at least 3-5 minutes).
You can also add Super plasticizer to the water 10-15 minutes prior to casting (until plasticizer dissolves in water), then mix with dry ingredients.
Please note:
Concrete minimum mixing time is 3 minutes with mechanical drill or 5 minutes with mortar mixer (it takes a few minutes until Super Plasticizer, Melment F 10, absorbs into the cement and start reaction).
Plasticizer recommended dosage of Melment F 10 is 0.20-2% by Cement weight.
Please note:
Super plasticizer dosage rate calculated by Cement weight, not total concrete weight
HOW TO MIX MELMENT F 10 WITH GYPSUM:
Add Melment F 10 to the water 10-15 minutes prior mixing until Melment F 10, dissolves in water, then add gypsum to pre-measured water and mix with mechanical drill.
Melment F 10, dosage rate - 0.25% by Gypsum weight.
Water-55% by Gypsum weight.
CHARACTERISTICS / CHEMISTRY OF MELMENT F 10:
Melment F 10 is a free-flowing, spray dried powder of a sulphonated polycondensation product based on melamine.
ADVANTAGES OF MELMENT F 10:
■ Melment F 10 increases the durability of powder products by reducing the mixing water.
■ While Melment F 10 reduces the mixing water of powder products, it increases their workability.
■ Melment F 10 does not change the colors of powdered products.
■ Melment F 10 can be easily mixed with water on site to obtain liquid superplasticizer.
■ To increase the workability and strength of the mixture, at a rate of 0.5 - 0.9 kg,
■ For leveling screeds and precast plaster elements at a rate of 0.6 -1.5 kg,
■ Melment F 10 is used at a rate of 0.5 -1.5 kg for plaster molds.
FEATURES OF MELMENT F 10:
*Precise pH value
*Optimum quality
*Purity
COMPOSITION AND PROPERTIES OF MELMENT F 10:
Chemical composition:
Melment F 10 is a sulphonated powder product of melamine-based polycondensation obtained by spray drying.
Melment F 10 is optimized for plasticization and reduction of water consumption for cement- and gypsum-based mixtures.
DOSAGE OF MELMENT F 10:
0.2–1.5 wt.% by weight of binder.
0.05–0.10 wt.% by weight of binder (when used as a dispersant).
PHYSICAL and CHEMICAL PROPERTIES of MELMENT F 10:
Physical shape: powder
Appearance: white to slightly colored
Drying loss: max. 4.0%
Bulk density: 500 – 800 kg/m³
Dosage recommendation: in relation to weight of binder 0.20 to 2.00
pH value: at 20 ˚C, 20% solution 9.0– 11.4
Physical shape: powder
Appearance: white to slightly colored
Drying loss, [%]: max. 4.0
Bulk density, [kg/m3]: 500 to 800
pH-value (20 °C), 20 % solution: 9 to 11.4
Dosage recommendation, [%] in relation to weight of binder: 0.20 to 2.00
Physical shape powder
Appearance characteristic, white to slightly colored
Drying loss max. 4.0%
Bulk density 500 – 800 kg/m³
Dosage recommendation 0.20 – 2.00%
by weight of cementitious materials
pH value at 20 ˚C, 20% solution 9.0 – 11.4
Physical shape: powder
Appearance: white to slightly colored
Drying loss, [%]: max. 4.0
Bulk density, [kg/m³] ：500 to 800
pH-value (20 °C), 20 % solution：9.0 to 11.4
Dosage recommendation, [%] in relation to weight of binder ：0.20 to 2.00
Product Name: MELMENT F 10
CAS Number: 25214-70-4
EC Number: 246-350-2
Molecular Formula: C12H18N2O3
Molecular Weight: 234.28 g/mol
Appearance: Light yellow to brownish powder
pH: 4.0 to 7.0 (in 1% solution)
Density: Approximately 1.05 g/cm³
Solubility: Soluble in water
FIRST AID MEASURES of MELMENT F 10:
-Description of first-aid measures
*General advice:
Show this material safety data sheet to the doctor in attendance.
*If inhaled:
After inhalation:
Fresh air.
*In case of skin contact:
Take off immediately all contaminated clothing.
Rinse skin with
water/ shower.
*In case of eye contact:
After eye contact:
Rinse out with plenty of water.
Call in ophthalmologist.
Remove contact lenses.
*If swallowed:
After swallowing:
Immediately make victim drink water (two glasses at most).
Consult a physician.
-Indication of any immediate medical attention and special treatment needed.
No data available
ACCIDENTAL RELEASE MEASURES of MELMENT F 10:
-Environmental precautions:
Do not let product enter drains.
-Methods and materials for containment and cleaning up:
Cover drains.
Collect, bind, and pump off spills.
Observe possible material restrictions.
Take up dry.
Dispose of properly.
Clean up affected area.
FIRE FIGHTING MEASURES of MELMENT F 10:
-Extinguishing media:
*Suitable extinguishing media:
Carbon dioxide (CO2)
Foam
Dry powder
*Unsuitable extinguishing media:
For this substance/mixture no limitations of extinguishing agents are given.
-Further information:
Prevent fire extinguishing water from contaminating surface water or the ground water system.
EXPOSURE CONTROLS/PERSONAL PROTECTION of MELMENT F 10:
-Control parameters:
--Ingredients with workplace control parameters:
-Exposure controls:
--Personal protective equipment:
*Eye/face protection:
Use equipment for eye protection.
Safety glasses
*Body Protection:
protective clothing
*Respiratory protection:
Recommended Filter type: Filter A
-Control of environmental exposure:
Do not let product enter drains.
HANDLING and STORAGE of MELMENT F 10:
-Conditions for safe storage, including any incompatibilities:
*Storage conditions:
Tightly closed.
Dry.
STABILITY and REACTIVITY of MELMENT F 10:
-Chemical stability:
The product is chemically stable under standard ambient conditions (room temperature) .
-Possibility of hazardous reactions:
No data available
