Zinc Chloride ZnCl2 65 %, also known as Zinc Chloride, Zinc Chloride, Zinc Dichloride and Zinc(II) Chloride, is a highly concentrated inorganic salt solution containing approximately 65% by weight dissolved in water of Zinc Chloride, defined by CAS No 7646-85-7 and EC No 231-592-0. The active ingredient, ZnCl2, has a molecular formula of ZnCl2 and a molar mass of approximately 136.3 g/mol. Since the commercial product contains approximately 65% Zinc Chloride and 35% water, it is not a pure compound, but rather a concentrated aqueous solution, and therefore no single molecular weight is assigned to the entire solution.
65% Zinc Chloride solution is a clear, high-density and strongly acidic liquid that can vary from colorless to light yellow. In current commercial samples, the ZnCl2 content is given as 65% by weight. In a documented commercial grade, the solution density is approximately 1.85 g/mL. This value may vary according to temperature and actual concentration. The theoretical amount of zinc in a 65% solution is approximately 31.2%. This value is obtained by multiplying the zinc mass share in ZnCl2 by the 65% active substance ratio in the solution.
Zinc Chloride ZnCl2 65 % can be used in metal surface preparation, galvanizing fluxes, brazing fluxes, battery and electrolyte systems, textiles, paper, chemical synthesis, rubber and resin processes, activated carbon production, oil and gas applications, and various laboratory or industrial chemical processes. The product exhibits strong Lewis acid character and is extensively hydrated in water. The high chloride and zinc ion content provides both chemical reactivity and high ionic strength.
Zinc Chloride 65% solution can help remove oxide layers, especially on metal surfaces, and prepare the surface for subsequent treatment. When used in galvanizing and brazing fluxes with ammonium chloride, it contributes to dissolving metal oxides and reducing re-oxidation. However, it exhibits a strongly corrosive character due to its high chloride content. Incorrect material selection, improper storage, or uncontrolled contact can cause serious equipment corrosion and safety risks.
WHAT IS ZINC CHLORIDE ZnCl2 65 %?
Zinc Chloride ZnCl2 65% is a concentrated aqueous solution containing approximately 65% Zinc Chloride by weight. The product is not pure anhydrous Zinc Chloride. The remaining portion of the commercial solution is largely water. A nominal 65% concentration means that there is approximately 65 kg of ZnCl2 in 100 kg of solution. Therefore, although the formula of the solution is written as ZnCl2, this expression describes the dissolved active salt. The whole liquid mixture is not a single pure molecule. Zinc Chloride has a very high solubility in water. It shows strong hydration interactions with water. As the concentration increases, the density, viscosity, ionic strength and corrosion behavior of the solution change. It is a 65% grade high concentration commercial solution. Lower concentrations can be prepared by diluting with water. For example, if a 50% ZnCl2 solution is desired to be prepared, the 65% stock solution is diluted with deionized water in a controlled manner.
Water addition and mixing should be controlled as heat may be released during dilution. Zinc Chloride 65% shows strong Lewis acid properties. The zinc ion can act as the center that can accept electron pairs. Therefore, it can act as a catalyst or activator in some organic and inorganic reactions.
Complex zinc-chloride and hydrated zinc species can form in water. In addition to simple free Zn2+ and Cl- ions, complex species such as ZnCl+, ZnCl3- or ZnCl4²- can also be found in concentrated solutions. This distribution depends on concentration, temperature and chloride activity.
The main functions of the product:
Helping to dissolve metal oxide layers
Providing surface activation in galvanizing fluxes
Supporting oxide removal in brazing fluxes
Providing high ionic conductivity
Being a source of zinc in zinc-containing electrolyte systems
Acting as a Lewis acid catalyst
Used as an activator in chemical synthesis
To be used in the chemical activation of cellulosic materials
Used as a chemical activation agent in the production of activated carbon
To be used in certain chemical processes in textile and paper processes
Providing chloride and zinc ion in battery electrolytes
To play a catalytic or process auxiliary role in resin and polymer chemistry
Zinc Chloride 65% and anhydrous ZnCl2 are not the same product.
Anhydrous Zinc Chloride is a solid.
65% solution is liquid.
The purity and water content of the solid product are different.
No two products used in the same mass provide the same amount of active ZnCl2.
For example, 10 kg of a 65% solution contains approximately 6.5 kg of ZnCl2.
For this reason, the active substance ratio of the commercial solution should be used in formulation and process calculations.
COMMON PRODUCT AND CHEMICAL NAMES
Zinc Chloride ZnCl2 65 %
Zinc Chloride 65%
Zinc Chloride 65 % Solution
Zinc Chloride Solution 65%
Zinc Chloride Solution
Zinc Chloride
Zinc Chloride
Zinc Dichloride
Zinc(II) Chloride
ZnCl2 Solution
CAS NO, EC / EINECS NO AND CHEMICAL IDENTIFICATION
Product Name: Zinc Chloride ZnCl2 65%
English name: Zinc Chloride 65% solution
Key active chemical: Zinc Chloride
Chemical formula: ZnCl2
CAS No: 7646-85-7
EC/EINECS No: 231-592-0
Molar mass of ZnCl2: About 136.3 g/mol
Commercial product type: Concentrated aqueous solution
Active ZnCl2 ratio: Approximately 65% by weight
Water and other minor ingredients: Approx. 35%
Theoretical zinc content: Approx. 31.2 wt%
Theoretical chlorine content: Approx. 33.8 wt%
Physical form: Liquid
Appearance: Clear, colorless to light yellow
Density: Approximately 1.85 g/mL at certified 65% commercial grade
Acid-base character: Strongly acidic
Ionic character: High ionic strength
Miscibility with water: High
Main function: Zinc and chloride ion source
In a current 65% Zinc Chloride solution technical sheet, the ZnCl2 content is given as 65%.
In the same document, ZnO is stated as a maximum of 0.65%, sulfate as a maximum of 0.005%, iron as a maximum of 0.0003%, lead as a maximum of 0.0003%, cadmium as a maximum of 0.0001% and barium as a maximum of 0.05% as basic salt equivalent.
These values are not universal limits for all 65% products.
It is a commercial specification of a particular manufacturer.
The COA and TDS values of the actual product should be taken as basis at the time of purchase.
CHEMICAL STRUCTURE AND MOLECULAR PROPERTIES OF ZINC CHLORIDE ZnCl2 65 %
Zinc Chloride is basically an ionic inorganic compound consisting of Zn2+ and chloride ions. In solid form, the structure of ZnCl2 should not be considered as an idealized simple two-ion molecule. There are coordinated zinc-chloride types in crystal and molten structure. When dissolved in water, the zinc ion is strongly hydrated. Water molecules form coordination around the zinc center. As chloride concentration increases, chlorozinc complexes may form. In concentrated 65% solution, the species distribution is different from in dilute solution. Zn2+ is not only found as a free hydrated ion. ZnCl+, ZnCl2 species, ZnCl3- and ZnCl4²-like complex species can also be found in equilibrium. This complexation is important in a high chloride environment. Zinc chloride is Lewis acid. Zinc can accept central electron pairs. This property can help activate carbonyl groups or other electron donor functions in organic reactions. For this reason, ZnCl2 can be used as a catalyst or activator in Friedel-Crafts type reactions, ether dissociations, condensation and other syntheses. It shows high affinity with water.
Anhydrous Zinc Chloride is very hygroscopic and can extract moisture from the air. Because there is already a high amount of water in the 65% solution, the behavior is different, but the concentration can change in contact with environmental humidity. A decrease in concentration can alter density and process performance. The acidic character of the Zinc Chloride solution is due to the zinc ion polarizing the water molecules. The hydrated zinc ion can facilitate proton separation from water molecules. For this reason, aqueous ZnCl2 solutions show acidic pH. The exact pH depends on the concentration, basic salt content, and measurement method. pH measurement with a standard glass electrode in a 65% solution should be interpreted with caution due to the high ionic strength.
Chemical properties of Zinc Chloride 65% solution:
High zinc ion content
High chloride ion content
High ionic strength
Strong Lewis acid character
Acidic aqueous environment
High tendency to absorb water
High electrical conductivity
Reaction with metal oxides
Ability to form zinc hydroxide or basic zinc salts with bases
Ability to create complex flux systems with ammonium chloride
Concentration-dependent complex ion distribution
PHYSICAL AND CHEMICAL PROPERTIES OF ZINC CHLORIDE ZnCl2 65 %
65% Zinc Chloride solution is a high density, clear and corrosive liquid.
General technical specifications:
Physical form: Liquid
Color: Colorless to light yellow
ZnCl2 concentration: About 65%
Water content: Approx. 35%
Molar mass of ZnCl2: 136.3 g/mol
Theoretical Zn content: Approx. 31.2%
Density: Commercial values of approximately 1.8-1.9 g/mL can be seen
Documented commercial sample: Approximately 1.85 g/mL
Dilution with water: Whole
pH: Acidic, exact value depends on the product and measurement condition
Viscosity: Concentration and temperature dependent
Crystallization behavior: Concentration and temperature dependent
Electrical Conductivity: High
Evaporable component: Mainly water
Flammability: Aqueous ZnCl2 solution is non-flammable. 65 % The density of the solution depends on temperature.
As the temperature rises, the density usually decreases. Therefore, the effect of temperature must be taken into account in processes using volumetric dosing.
Mass dosing may be more reliable. Highly concentrated solutions of Zinc Chloride can crystallize at low temperature.
The exact crystallization temperature should not be determined only from the nominal value of 65%.
Basic salt content, total ZnCl2, water, and impurities can alter crystallization behavior.
The product storage temperature should be selected according to the supplier's technical document.
When diluting with water, the mixture may heat up. Therefore, large-volume dilution requires controlled addition of the solution to water, stirring, and temperature monitoring.
Significant heat can develop during the reaction with concentrated acids or bases.
HOW DOES ZINC CHLORIDE ZnCl2 65% WORK AT THE MOLECULAR LEVEL?
The working mechanism of Zinc Chloride 65% is different according to the application. The basic mechanism in metal surface fluxes is the chemical dissolution of the oxide layer.
Oxide and hydroxide films can form on iron, steel, copper, or brass surfaces. These layers prevent metal-to-metal contact during galvanizing or brazing.
The flux system containing ZnCl2 and NH4Cl helps to dissolve metal oxides and keep the surface active. Once the surface is cleaned, the molten zinc or solder alloy can be better spread over the metal surface. Another task of surface flux in galvanizing is to reduce reoxidation. Acid-cleaned steel can be reoxidized when it comes into contact with air.
ZnCl2/NH4Cl based flux film can protect the surface before hot dip. In battery electrolytes, ZnCl2 provides high ionic conductivity and zinc-chloride complex chemistry.
In classical zinc-carbon and zinc chloride type dry cells, ZnCl2 can be used as an electrolyte in combination with NH4Cl or at higher ZnCl2 ratios.
The electrolyte provides ion transport between the zinc anode and cathode system. In chemical synthesis, ZnCl2 activates electron-dense regions as Lewis acid.
For example, it can make carbonyl carbon more electrophilic by coordinating with carbonyl oxygen.
In this way, nucleophilic reactions can be facilitated. In the production of activated carbon, ZnCl2 penetrates into the lignocellulosic precursor. During heating, dehydration can affect aromatization and pore formation.
The activation temperature, the ZnCl2/precursor ratio, and the washing process determine the pore structure formed. Here, the adsorption function does not belong directly to the ZnCl2 solution, but to the well-washed activated carbon formed at the end of the process.
System-level functions of Zinc Chloride 65 %:
Dissolving metal oxides
Preparing the surface for galvanizing
Supporting solder wetting
Providing electrolyte conductivity
Being a source of zinc ions
Forming a chloride complex
Lewis acid to catalyze
Chemically activating cellulosic precursors
Creating high ionic strength
Supporting the dissolution of basic zinc compounds
IN WHICH SECTORS IS ZINC CHLORIDE ZnCl2 65 % USED?
Main areas of use:
Hot-dip galvanizing
Soldering fluxes
Metal surface preparation
Battery and electrolyte systems
Zinc-carbon batteries
Zinc chloride-type dry cells
Chemical synthesis
Organic synthesis catalysis
Activated carbon production
Biomass activation
Textile
Paper and pulp
Rubber
Resin
Oil and gas
Laboratory chemistry
Production of zinc salt
Pigment and catalyst precursors
Metalworking chemicals
USE OF ZINC CHLORIDE ZnCl2 65 % IN GALVANIZING AND SOLDERING
One of the most common technical applications of Zinc Chloride is galvanizing fluxes. The steel surface is degreased and pickled before hot-dip galvanizing.
These processes remove iron oxides and surface impurities. However, the clean surface can quickly reoxidize.
The flux solution containing ZnCl2 and NH4Cl is applied to the steel surface, helping to dissolve any remaining oxides and protect the surface until molten zinc.
When ammonium chloride is heated and reacts on the surface, it can promote oxide removal.
ZnCl2 wets the metal surface at high temperature and contributes to the dissolution of oxide layers. The total salt concentration of the flux bath, ZnCl2/NH4Cl ratio, iron accumulation, pH and temperature affect the galvanizing quality.
Excessive iron contamination can increase dross formation. Incorrect flux density can affect drying and zinc consumption.
Therefore, the flux bath should be analyzed regularly. In soldering fluxes, ZnCl2 can also dissolve metal oxides, making it easier for solder to spread on a copper, brass, or steel surface.
However, ZnCl2 residues are corrosive. After soldering, the flux residue should be removed properly.
Due to the risk of residual corrosion and ionic conductivity in electronic circuits, active fluxes based on ZnCl2 require special control.
BATTERY AND ELECTROLYTE APPLICATIONS OF ZINC CHLORIDE ZnCl2 65 %
ZnCl2 solutions can be used as electrolyte components in classical zinc-carbon batteries and zinc chloride type dry cells.
The ZnCl2 ratio may be higher in zinc chloride-type cells than in conventional Leclanché systems.
It provides electrolyte ion transport.
Zinc participates in anode dissolution reactions.
Chloride ion can help retain zinc species in solution.
The electrolyte composition affects the battery's internal resistance, low-temperature performance, shelf life, and discharge behavior.
In industrial battery formulation, not only ZnCl2 concentration but also NH4Cl, water amount, inhibitors, manganese dioxide cathode and separator system are evaluated together.
The 65% ZnCl2 solution may not be used directly as the final electrolyte in battery production.
It can be adjusted according to the process requirement by diluting it to lower target concentration or mixing it with NH4Cl.
IS ZINC CHLORIDE ZnCl2 65 % USED IN FOOD?
Zinc Chloride is a chemical that can be considered a source of zinc in very specific food or nutrition applications in certain regulatory systems.
However, industrial Zinc Chloride ZnCl2 65% solution should not be used directly as a food additive.
Zinc Chloride for use in a food, pharmaceutical or nutritional application must meet specific purity class, heavy metal limits and relevant regulatory requirements.
If the technique is produced for 65% solution galvanizing, chemical processing, or metalworking, it is not suitable for addition to food.
In food or supplement application, product grade and regulatory compliance must be verified separately.
INDUSTRIAL APPLICATIONS OF ZINC CHLORIDE ZnCl2 65 %
Zinc Chloride 65% can be used as a source of highly concentrated ZnCl2 in chemical synthesis.
Lewis acid can be used in reactions that require catalysis.
It can act as a catalyst or activator in some resin and polymer reactions.
In cellulose and biomass chemistry, its strong dehydration and complexation properties can be exploited.
In the production of activated carbon, ZnCl2 can be used as a chemical activation agent.
Biomass is impregnated with ZnCl2 solution.
It is then carbonized at controlled temperature.
ZnCl2 influences dehydration and aromatization processes.
After carbonization, zinc-containing residues need to be carefully washed away.
Inadequate washing can result in high zinc and chloride residue in the final activated carbon.
Wastewash water can carry a high zinc load and requires environmental treatment.
In textile and paper processes, ZnCl2 can be used in certain special chemical processes.
However, due to the high corrosiveness and wastewater metal load, the intended use in modern processes must be carefully considered.
Heavy saline fluid systems and zinc-containing high-density brins have historically been used in oil and gas applications.
ZnCl2 contributes to providing high density, but environmental and corrosion risks are high.
WHAT PROBLEMS CAN ZINC CHLORIDE ZnCl2 65 % SOLVE?
Oxide layer remaining on the surface before galvanizing
The ZnCl2/NH4Cl flux system can help dissolve metal oxides.
Re-oxidizing clean steel
The flux film can temporarily protect the surface before hot dip.
Poor spread of solder on the metal surface
It can improve solder wetting by removing the ZnCl2 oxide layer.
Insufficient ion conductivity in the electrolyte
ZnCl2 can provide high ion concentration.
The need for Lewis acid catalysis in chemical synthesis
ZnCl2 can act as catalyst accepting electron pair.
The need to produce high surface area activated carbon from biomass
ZnCl2 can be used as a chemical activation agent.
Insolubility of metal oxide or basic zinc compound
Acidic and chloride medium can support solubility.
If the problem persists, only the ZnCl2 concentration should not be increased.
Temperature, NH4Cl ratio, metal surface condition, pH, iron contamination, water amount and process time should be evaluated together.
THINGS TO CONSIDER WHEN USING ZINC CHLORIDE ZnCl2 65 %
65% Zinc Chloride solution is strongly corrosive. Eye and skin contact should be avoided.
Appropriate chemical gloves should be used. A face shield or safety glasses should be used.
Acid and chloride resistant equipment should be preferred. Carbon steel can suffer serious corrosion under many conditions. Tank and pipe material should be selected according to the actual process temperature.
Heat may be released when diluting the product. Controlled mixing should be carried out.
Rapid addition of a large amount of water to the concentrated solution can cause a localized temperature rise. The dilution procedure should be carried out according to the chemical safety rules of the enterprise.
Contact with bases may cause zinc hydroxide precipitation. Basic zinc salts may form with carbonates.
Zinc sulfide precipitation may occur with sulfurous substances. Iron accumulation should be monitored in metal flux baths.
Wastewater containing zinc should not be discharged directly into the drain. Zinc can be harmful to the aquatic environment. Wastewater should be passed through a metal precipitation or appropriate treatment process.
TDS should be examined. SDS should be examined. COA should be checked.
The 65% active ingredient ratio must be verified on a batch basis.
INITIAL FORMULATION APPROACHES FOR ZINC CHLORIDE ZnCl2 65%
EXAMPLE 1: ZnCl2-NH4CL FLUX SOLUTION FOR HOT DIP ELECTROPLATING
Objective: Evaluation of Zinc Chloride ZnCl2 65% stock solution with ammonium chloride in steel surface activation and flux performance before galvanizing.
Starting composition:
Deionized water: 48.00%
Zinc Chloride ZnCl2 65% solution: 32.00%
Ammonium chloride: 19.50%
Nonionic low-foam C9-11 alcohol ethoxylate, 6 EO: 0.20%
Sodium benzoate: 0.10%
Citric acid monohydrate: 0.20%
Total: 100%
The 65% ZnCl2 solution used at 32% in this starter mix provides approximately 20.8% active ZnCl2.
The ammonium chloride ratio is approximately 19.5%.
This recipe is not a verified commercial flux recipe of a specific galvanizing line.
The actual flux composition should be optimized according to the steel chemistry, pickling line, drying, galvanizing bath, and target coating quality.
Application approach:
The deionized water is taken into the mixing tank.
Ammonium chloride is dissolved in a controlled manner.
The mixture temperature is monitored.
Zinc Chloride ZnCl2 65% solution is added slowly.
The mixture is stirred until homogeneous.
Nonionic wetting agent is added.
Sodium benzoate and citric acid are solubilized.
Density is measured.
Total ZnCl2 and NH4Cl analysis is performed.
The iron content is determined at the beginning.
Acid-cleaned steel coupons are immersed in flux.
After drying, the surface film is examined.
Coupons are galvanized in a laboratory type zinc bath.
Coating appearance, bare spot, ash formation, and adhesion are evaluated.
The effect of iron accumulation on performance in the flux solution is tested separately.
EXAMPLE 2: ZINC CHLORIDE BASED LABORATORY TYPE ZINC-CARBON ELECTROLYTE SOLUTION
Objective: Evaluation of Zinc Chloride ZnCl2 65% stock solution together with ammonium chloride as ionic phase in classical zinc-carbon battery electrolyte.
Starting composition:
Deionized water: 53.00%
Zinc Chloride ZnCl2 65% solution: 30.00%
Ammonium chloride: 16.00%
Zinc oxide: 0.50%
Sodium benzoate: 0.20%
Magnesium chloride hexahydrate: 0.30%
Total: 100%
The 65% ZnCl2 solution used at 30% in this starter mixture provides approximately 19.5% active ZnCl2.
This recipe is not a commercial battery electrolyte.
The laboratory is the initial approach for the comparison study.
Actual battery performance depends on anode alloy, manganese dioxide, separator, inhibitor, and cell design.
Application approach:
Deionized water is taken into the main container.
Ammonium chloride is completely dissolved.
Zinc Chloride ZnCl2 65% is added in a controlled manner.
Zinc oxide is added in small portions to evaluate the buffering of the system.
Magnesium chloride is solubilized.
Sodium benzoate is added.
The solution is homogenized.
Density and conductivity are measured.
pH or acidity is recorded by the appropriate method.
Corrosion testing is performed on laboratory zinc anode coupons.
The electrolyte is compared to different levels of ZnCl2.
Targets of 15%, 20%, and 25% active ZnCl2 can be evaluated in separate samples.
Each change is balanced by the amount of deionized water, maintaining a total of 100%.
PRODUCTS SIMILAR TO ZINC CHLORIDE ZnCl2 65 % & alternatives
Application should be considered when determining the Zinc Chloride 65% alternative.
The alternative in galvanizing flux is not the same as the alternative in battery electrolyte.
Zinc Chloride solid, Ammonium chloride, Zinc bromide, Calcium chloride, Magnesium chloride and different Lewis acids
It can be alternative or complementary depending on the application.
Anhydrous Zinc Chloride provides high active substance.
It does not contain transport water.
However, it is hygroscopic and requires a solubilization process.
The 65% solution, on the other hand, can be pumped and dosed directly.
Ammonium chloride works synergistically with ZnCl2 in galvanizing and brazing fluxes.
It does not always provide the same oxide dissolution and surface protection performance on its own.
Zinc bromide can be used in higher density heavy saline fluids.
However, the cost and bromide chemistry are different.
Calcium chloride and magnesium chloride can provide lower environmental burden in high-density brine systems, but not the Lewis acid and zinc chemistry of ZnCl2.
QUALITY CONTROL AND PURCHASING CRITERIA FOR ZINC CHLORIDE ZnCl2 65 %
When purchasing Zinc Chloride ZnCl2 65 %, one should not only look at the nominal 65%.
Recommended information to review before purchasing:
Full product name
Manufacturer
CAS No 7646-85-7
EC No 231-592-0
ZnCl2 concentration
Total zinc
Density
Outlook
Color
Basic salt content
ZnO equivalent
Iron
Lead
Cadmium
Barium
Sulfate
Free acidity
pH or acidity method
Crystallization behavior
Packaging
Origin
Batch number
Shelf life
TDS
SDS
COA
In a current 65 % solution technical sheet:
ZnCl2: 65%
ZnO equivalent basic salt: no more than 0.65%
Sulfate: not more than 0.005%
Iron: no more than 0.0003%
Lead: no more than 0.0003%
Cadmium: no more than 0.0001%
Barium: no more than 0.05%
values such as are given.
These values are examples for the relevant commercial class only.
The specification of the product to be ordered should be verified separately.
Iron and basic salt content is important in galvanizing application.
Metal impurities and acidity may be more critical in battery application.
The amount of water and purity can be important in chemical synthesis.
Therefore, quality criteria should be selected according to the target application.
STORAGE AND HANDLING OF ZINC CHLORIDE ZnCl2 65 %
Zinc Chloride 65% is a corrosive chemical solution. It should be stored in suitable chemical resistant tanks.
The tank material should be selected in accordance with chloride and high ZnCl2 concentration. Carbon steel may not be suitable in many conditions. Suitable polymer-coated tanks or materials recommended by the manufacturer can be considered.
The exact selection of material should be based on temperature and concentration. The tank lid should be kept closed. Dilution and atmospheric contamination should be avoided.
The risk of crystallization at low temperature should be evaluated. Tank heating can be used if necessary. Heating should not be done uncontrollably. High temperature can increase corrosion. It should be kept away from strong bases.
Contact with reactive metals should be limited. Uncontrolled mixing with sulfur chemicals should not be made.
The packaging and secondary retention system must be suitable for the corrosive solution.
The transport classification should be checked against the current SDS document.
Zinc Chloride solutions may be subject to classifications of corrosive and hazardous to the environment.
ZINC CHLORIDE ZnCl2 65 % SAFETY INFORMATION
Zinc Chloride 65% is a strongly corrosive solution. It can cause serious eye damage.
It can cause chemical burns on the skin. Inhaling steam or mist can irritate the respiratory tract.
High-temperature ZnCl2 fog is particularly dangerous. Safety goggles and a face shield should be used.
Acid and chloride resistant chemical gloves should be used. Protective work clothes should be worn.
In processes where aerosols or fogs are generated, appropriate respiratory protection should be evaluated. In case of contact with eyes, immediate prolonged flushing with water is necessary.
Contaminated clothing that comes into contact with the skin should be removed. Spillage should be controlled.
Zinc-containing liquid should be prevented from reaching drains and surface water. ZnCl2 can be harmful to aquatic organisms.
Wastewater should be diverted to appropriate metal treatment. Zinc hydroxide precipitation and heat release should be considered during neutralization with the base.
Neutralization should be carried out under controlled and engineered measures. Exact H statements, P statements, transport class and personal protective equipment should be verified from the current SDS document of the commercial product used.
WHAT TO CONSIDER WHEN BUYING ZINC CHLORIDE ZnCl2 65 %?
First, the target application should be determined.
Galvanization?
Soldering flow?
Battery electrolyte?
Activated carbon production?
Chemical synthesis?
This choice changes the quality criteria.
The following information should be clarified before ordering:
Is ZnCl2 concentration really 65%?
What is the tolerance range?
What is density?
What is the basic salt content?
What is the iron level?
What are the limits of lead and cadmium?
What is the sulfate level?
What is the barium level?
Is the view clear?
Is there a sediment?
What is crystallization behavior?
What is packaging material?
What is origin?
Is there TDS?
Is there SDS?
Is COA provided on a batch basis?
Price comparison should not be made only on kilograms of solution.
The cost per active ZnCl2 should be calculated.
A 65% solution carries about 35% water.
In comparison with solid ZnCl2, solubilization, storage, pumpability, and labor cost should be considered together.
ZINC CHLORIDE ZnCl2 65 % SUPPLY FROM ATAMAN KIMYA
Zinc Chloride ZnCl2 65 % is a highly concentrated Zinc Chloride solution used in galvanizing, brazing, metal surface preparation, battery electrolytes, activated carbon production, chemical synthesis and various industrial processes. Companies that want to get information about the supply of Zinc Chloride ZnCl2 65 % from Ataman Kimya can share their target applications, required purity level, iron and heavy metal limits, packaging preferences and technical document needs, facilitating appropriate product evaluation.
Before ordering, active ZnCl2 ratio, density, appearance, basic salt, sulfate, iron, lead, cadmium, barium, TDS, SDS and COA information should be evaluated together.
Since the product is corrosive, the choice of packaging and storage material is an important part of the procurement decision.
It should be taken into account that solid Zinc Chloride and 65% solution cannot be used in the same dose.
FREQUENTLY ASKED QUESTIONS ABOUT ZINC CHLORIDE ZnCl2 65 %
What is Zinc Chloride ZnCl2 65 %?
It is a concentrated aqueous solution containing approximately 65% Zinc Chloride by weight.
What is a CAS number?
7646-85-7.
What is an EC number?
231-592-0.
What is its chemical formula?
For active salt, it is ZnCl2.
What is molecular weight?
For ZnCl2, it is about 136.3 g/mol.
Does the entire 65% solution have a molecular weight?
The solution is a mixture and is not assigned a single molecular weight to the whole of it.
What is the approximate ratio of zinc in 65% solution?
Theoretically, it is about 31.2%.
What is its density?
Values of approximately 1.8-1.9 g/mL can be seen in commercial 65% solutions. A documented commercial sample provided approximately 1.85 g/mL.
What is its color?
It is usually clear, colorless to light yellow liquid.
What is the pH value?
It has a strongly acidic character. The exact value varies according to the product and measurement method.
Is it diluted with water?
Yes.
Is heat released during dilution?
Yes, significant heat can develop when diluting a highly concentrated salt solution.
Is it used in galvanizing?
Yes.
Is it used in soldering flux?
Yes.
Can it be used with ammonium chloride?
Yes. It is the common combination in galvanizing and brazing fluxes.
Is it used in battery electrolyte?
Yes. It can be used in zinc chloride type dry cells and zinc-carbon electrolyte systems.
Is activated carbon used in production?
Yes. It can be used in the chemical activation of biomass and carbon precursors.
Is Lewis acid?
Yes.
Is it used in food?
The technical 65% solution should not be used directly as a food additive.
Is it corrosive?
Yes, it is strongly corrosive.
Can carbon steel be stored in a tank?
Suitability should be carefully considered due to chloride and acidic environment. Tank material should be selected based on process temperature and concentration.
Can it be given to wastewater?
Uncontrollably no. Zinc-containing wastewater requires proper treatment.
Is solid the same as ZnCl2?
The chemical active is the same, but the physical form and the ratio of active substance are different.
What documents should be requested?
TDS, SDS, and COA are essential documents.
ZINC CHLORIDE ZnCl2 65 % - TECHNICAL SUMMARY
Zinc Chloride ZnCl2 65% is concentrated aqueous solution containing approximately 65% Zinc Chloride and approximately 35% water by weight.
The CAS No value of Zinc Chloride is 7646-85-7. The EC No value is 231-592-0. Its chemical formula is ZnCl2 and its molar mass is approximately 136.3 g/mol. No single molecular weight is assigned to the entire commercial solution. The theoretical amount of zinc in a 65% solution is approximately 31.2%. The product is usually clear, colorless to light yellow liquid.
In commercial 65% solutions, the density can be about 1.8-1.9 g/mL. In a documented commercial grade, a density of about 1.85 g/mL is given.
Zinc Chloride is a 65% acidic and high ionic strength solution. It can help dissolve metal oxides in galvanizing fluxes and keep the surface active. It can support oxide removal and wetting in brazing fluxes. It provides high ionic conductivity and zinc-chloride chemistry in battery electrolytes. It can be used as Lewis acid in chemical syntheses.
It can be considered as a chemical activation agent in activated carbon production. The product is strongly corrosive. Contact with eyes, skin, and equipment can pose a serious risk. Zinc-containing wastewater requires proper treatment.
ZnCl2 concentration, density, basic salt, iron, sulfate, lead, cadmium, barium, TDS, SDS, and COA should be evaluated together at the time of purchase.
Companies planning to procure Zinc Chloride ZnCl2 65 % from Ataman Kimya are advised to confirm the appropriate product by specifying the target application, quality class, impurity limits, packaging, and technical documentation requirements.